Setting the speaker distance Setting the speaker Level Playing a digital source Selecting an input source Selecting a preset station Playing a multichannel input source Using the Listening Modes Setting the listening mode parameters Other setup operations Recording a source European models only The initial settings Audio equipment connections Video equipment connections Playing a digital source Selecting an input source Selecting a preset station Playing a multichannel input source Using the Listening Modes Setting the listening mode parameters Assigning a video source.
Giving a name to each input source. Adjusting the output level of each speaker. Other setup operations Recording a source Receiving RDS broadcasts. European models only The initial settings Using the remote controller Programming the remote controller codes of.
Using a Macro function Troubleshooting guide Control positions and names Previous Page. Next Page. Onkyo integra tx-ds av receiver instruction manual 88 pages.
Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Audio Video Control Receiver.
Page 3: Precautions 3. AC Fuse The fuse is located inside the chassis and is not user-serviceable. For this no need registration. Please take a look at the below related repair forum topics. May be help you to repair. If you are not familiar with electronics, do not attempt to repair! You could suffer a fatal electrical shock!
Instead, contact your nearest service center! Before connecting the speakers, place them correctly by consulting the instruction manuals that came with your speakers. Produces a rich sound image by serving as a sound source for the Right and Left front speakers and enhancing the sonic movement.
Adds three-dimensional sonic movement and produces environmental sound associated with the background and effect sound for each scene. The sound recorded for the center speaker and the subwoofer will be properly distributed to the Right and Left front speakers and the Right and Left surround speakers for optimized surround playback.
Ideal speaker placement varies depending on the size of your room and the wall coverings. Here, only typical example of speaker placement and recommendations are shown. You can place your subwoofer anywhere in your room because the placement affects very little the perceived sound. Please check the following information and choose speakers with appropriate impedances for the connections.
If power amplifiers are used, connect each speaker to the corresponding power amplifier. When connecting an equalizer, remove these jumper plugs before connecting the audio connection cables. If this happens, use a wall outlet on a different circuit. Plug the power cord into an AC wall outlet.
Loosen the screws and wrap the wire around these screws. Then tighten the screws with a screwdriver. With your fingernail or a small screwdriver, press the stoppers outward and remove the cover. Remove the transformer wire A from slit B and insert it into slit C. Prepare the coaxial cable as shown in the diagram.
FM Remove the insulation at the end of the cable, then fully insert the stripped end of the cable. The FM indoor antenna is for indoor use only. Extend the antenna and move it in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion. If the reception is not very clear with the attached FM indoor antenna, the use of an outdoor antenna is recommended.
The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far away as possible from the unit, TVs, speaker cables, and power cords. When reception is not satisfactory with the attached AM loop antenna alone, connection of an outdoor antenna is recommended. Please make sure that you follow the considerations below regarding the location. It is dangerous to put the antenna close to power lines. Keep it well away from power lines, transformers, etc.
The outdoor antenna will be more effective if it is stretched horizontally above a window or outside. Using the OSD on-screen display function lets you display each screen on your TV so that you can perform various settings using only the remote controller. You can change this factory-set default as follows:. If the item has an additional screen, you can press the right edge of the button to change to that screen.
By pressing this button, you can follow in reverse the sequence in which you have displayed each setting screen. Finally, the onscreen display disappears. Use the on-screen display to set the background color, the superimpose mode, etc.
OFF : The on-screen display appears on the selected background color. Normal : The on-screen display is superimposed on images when video signals are input and shown on the selected background color when no video signal is input. Black : The on-screen display appears on black screen. For example, the volume level indicator appears on the screen when you increase the sound volume.
Turn it to select the parameter and press it to go to the next item. For the TX-DS, go to the next step. No : Your system is a non-THX speaker system. Set whether or not a subwoofer is connected. Yes: A subwoofer is connected. No: A subwoofer is NOT connected. Select the size of your front speakers. Large: Large front speakers are used. Small: Small front speakers are used. Select the size of your center speaker.
Large: A large center speaker is used. Small: A small center speaker is used. None: A center speaker is NOT used. Select the size of your surround speakers.
Large: Large surround speakers are used. Small: Small surround speakers are used. None: Surround speakers are NOT used. This sets all the connected speakers to THX speakers. The following steps are unnecessary. Select a value that is closest to the actual distance between each speaker and the listening position. Turn it to select the setting and press it to go to the next item. For each speaker, you can set a distance of 0. Set the distance from the left front speaker. Set the distance from the center speaker.
Set the distance from the Right front speaker. Set the distance from the Right surround speaker. Set the distance from the subwoofer. Select a value that is closest to the actual distance.
Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
0コメント